Talk:PH Meter
m (Reverted edits by 64.214.191.210 (Talk); changed back to last version by Eris) |
|||
Line 18: | Line 18: | ||
hmm, will it read but just not entirely to 0? Have you adjusted vr2 ? You may try changing the values of one of the two resistors r5 or r6.. | hmm, will it read but just not entirely to 0? Have you adjusted vr2 ? You may try changing the values of one of the two resistors r5 or r6.. | ||
+ | |||
+ | == первоклассный ремонт квартир и офисов по низким ценам Kayachals == | ||
+ | |||
+ | Строительно-инвестиционная компания ПРИОР предлагает : | ||
+ | - высококачественный ремонт квартир и офисов по самым низким ценам | ||
+ | - Евроремонт квартир ,коттеджей также офисных помещений с любым обьемом работ | ||
+ | - капитальный ремонт, реконструкция промышленых а также жилых зданий | ||
+ | - Очень качественный ремонт также реконструкция торговых, игровых а также развлекательных центров,медицинских,финансовых также правительственных учреждений. | ||
+ | - все виды строительно-инженерных, отделочных работ,покраска,побелка,стяжка,поклейка обоев ,плитка и пр. | ||
+ | - контроль а также гарантия качественного выполнения работ, | ||
+ | Гарантия. | ||
+ | Звоните нам : Киев, +38(044)353-67-58 . (066)270-1787 , http://remontkiev.org.ua |
Revision as of 15:44, 31 July 2010
Question : in the large circuit schematic, there seems to be a contradiction. The configuration table for the 14V version shows R1/R5/R6 as 10/10/12k respectively. It states on the right-hand side that the schematic itself is for the 14V version, but the schematic shows the other values.
I assume the schematic is correct and the column headers in the table are swapped. Please confirm ?
- i believe you're right. The circuit seems to be for 14v output but the table's values are swaped.. u_u sry. Don't have the program installed atm to edit it, will need to do so later unless maybe can photoshop it.. eris
Question: Is the pin numbering wrong on the TL062 chip? there is a ping 11? should'nt that bee pin 8? And if you look in the datasheet http://www.datasheetcatalog.org/datasheet/stmicroelectronics/2294.pdf
The voltage is swapped. pin 8 is Vcc+ and pin 4 is Vcc-
2009/03/23 - The above mentioned images have been corrected, and a capacitor was added to improve stability in noisy environments. :D
- I cant seem to get this to work on 0-14 or 0-5v. The readings will not go low enough.
op-amp: http://www.datasheetcatalog.org/datasheet/stmicroelectronics/2294.pdf
hmm, will it read but just not entirely to 0? Have you adjusted vr2 ? You may try changing the values of one of the two resistors r5 or r6..
первоклассный ремонт квартир и офисов по низким ценам Kayachals
Строительно-инвестиционная компания ПРИОР предлагает : - высококачественный ремонт квартир и офисов по самым низким ценам - Евроремонт квартир ,коттеджей также офисных помещений с любым обьемом работ - капитальный ремонт, реконструкция промышленых а также жилых зданий - Очень качественный ремонт также реконструкция торговых, игровых а также развлекательных центров,медицинских,финансовых также правительственных учреждений. - все виды строительно-инженерных, отделочных работ,покраска,побелка,стяжка,поклейка обоев ,плитка и пр. - контроль а также гарантия качественного выполнения работ,
Гарантия.
Звоните нам : Киев, +38(044)353-67-58 . (066)270-1787 , http://remontkiev.org.ua